Optical and electrical properties of ZnO/Mo/ZnO multilayer films processed at different annealing temperatures
Sign Up to like & getrecommendations! Published in 2019 at "Microsystem Technologies"
DOI: 10.1007/s00542-019-04453-9
Abstract: ZnO/Mo/ZnO transparent conductive thin films are deposited on Corning glass substrates using an RF magnetron sputtering system. The optical and electrical properties of the thin films are then examined following annealing for 40 min at temperatures… read more here.
Keywords: electrical properties; annealing temperatures; annealing temperature; zno zno ... See more keywords
Texture evolution and mechanical properties of Al–Mg–Si alloys at different intermediate annealing temperatures
Sign Up to like & getrecommendations! Published in 2019 at "Rare Metals"
DOI: 10.1007/s12598-019-01315-1
Abstract: Intermediate annealing treatment produces different effects on the state of particles in Al–Mg–Si alloy sheets, thereby affecting their recrystallization textures and formability. To improve the formability of the sheets, the effects of different intermediate annealing… read more here.
Keywords: annealing; texture evolution; annealing temperatures; evolution mechanical ... See more keywords
Influence of annealing temperatures on the magnetostructural transition and magnetocaloric effect of Ni40Co10Mn40Sn10 powders
Sign Up to like & getrecommendations! Published in 2017 at "Journal of Alloys and Compounds"
DOI: 10.1016/j.jallcom.2016.08.253
Abstract: Abstract The phase structure, the magnetostructural transition behavior and the associated magnetocaloric effect have been investigated in Ni 40 Co 10 Mn 40 Sn 10 bulk and powders, mainly focusing on the effects of annealing… read more here.
Keywords: bulk alloy; transition; annealing temperatures; magnetocaloric effect ... See more keywords
Annealing temperature dependence of the performance of bulk heterojunction polymer: Fullerene solar cells under short and open circuit conditions
Sign Up to like & getrecommendations! Published in 2020 at "Synthetic Metals"
DOI: 10.1016/j.synthmet.2020.116611
Abstract: Abstract The current density-voltage(J-V) characteristics and cole-cole impedance plots (-Im(Z) vs Re(Z)) of ITO/PEDOT:PSS/AnE-PVab:PCBM/Ca/Ag solar cells were measured under thermal annealing range 25–125 °C using AM 1.5 G (80 mW/cm2) solar simulator (white light). The fill factors (FF),… read more here.
Keywords: open circuit; cole cole; circuit conditions; annealing temperatures ... See more keywords
Structural and morphological characterization of sol-gel ZnO:Ga films: Effect of annealing temperatures
Sign Up to like & getrecommendations! Published in 2018 at "Thin Solid Films"
DOI: 10.1016/j.tsf.2017.11.042
Abstract: Abstract Sol-gel technology has been successfully applied for obtaining ZnO:Ga films by spin coating method. Their structural and optical properties are studied depending on the doping contents and on the annealing temperatures varying from 300… read more here.
Keywords: zno; annealing temperatures; gel zno; zno films ... See more keywords
Enhancing upconversion luminescence by annealing processes and the high-temperature sensing of ZnO:Yb/Tm nanoparticles
Sign Up to like & getrecommendations! Published in 2017 at "New Journal of Chemistry"
DOI: 10.1039/c7nj01358b
Abstract: Temperature that affects upconversion luminescence (UCL) is important to biological sensing and magnetic imaging. The temperature-dependent UCL of ZnO:Yb3+/Tm3+ nanoparticles (UCNP) was characterized. A detailed analysis of UCL spectra at different annealing temperatures revealed the… read more here.
Keywords: temperature; zno; annealing temperatures; upconversion luminescence ... See more keywords
Influence of Thermal Annealing Temperatures on Powder Mould Effectiveness to Avoid Deformations in ABS and PLA 3D-Printed Parts
Sign Up to like & getrecommendations! Published in 2022 at "Polymers"
DOI: 10.3390/polym14132607
Abstract: Fused deposition modelling (FDM)-printed parts can be treated with various post-processes to improve their mechanical properties, dimensional accuracy and surface finish. Samples of polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) parts are treated with… read more here.
Keywords: powder mould; printed parts; annealing temperatures; influence ... See more keywords