Comparison of internal fit of metal‐ceramic crowns in CAD/CAM and lost‐wax techniques in all fabrication stages through replica weighting, triple scanning, and scanning electron microscope
Sign Up to like & getrecommendations! Published in 2022 at "Clinical and Experimental Dental Research"
DOI: 10.1002/cre2.529
Abstract: Restoration fit is one of the prerequisites of clinical durability. It is controversial as to whether computer‐assisted design/computer‐aided milling (CAD/CAM) or lost‐wax fabrication methods result in more fit metal‐ceramic crowns. This in‐vitro study was conducted… read more here.
Keywords: cam lost; fabrication; fit metal; cad cam ... See more keywords
A multicenter survey on computer‐aided design and computer‐aided manufacturing mandibular reconstruction from Italian community
Sign Up to like & getrecommendations! Published in 2019 at "Microsurgery"
DOI: 10.1002/micr.30505
Abstract: Computer-aided design and computer-aided manufacturing (CAD/CAM) technology has revolutionized mandibular reconstructive surgery. The possibilities of planning margins of bone resection, flap segmentation, and plate design allow highly precise reconstructions with great improvement of functional and… read more here.
Keywords: reconstruction; cad cam; computer aided;
The effect of veneering on the marginal fit of CAD/CAM-generated, copy-milled, and cast metal copings
Sign Up to like & getrecommendations! Published in 2017 at "Clinical Oral Investigations"
DOI: 10.1007/s00784-017-2054-x
Abstract: ObjectiveThis in vitro study investigated the marginal fit of metal and zirconia copings before and after veneering on dies with shoulder/chamfer (s/c) finish lines.Materials and methodsUsing CAD/CAM, ten (n = 10) each s/c zirconia (NZ) copings and… read more here.
Keywords: cam; copy milled; marginal fit; cad cam ... See more keywords
Polishing effects and wear performance of chairside CAD/CAM materials
Sign Up to like & getrecommendations! Published in 2018 at "Clinical Oral Investigations"
DOI: 10.1007/s00784-018-2473-3
Abstract: ObjectivesTo investigate the surface roughness of CAD/CAM materials immediately after milling and after different chairside and labside polishing procedures. A two-body wear test was performed to compare the different wear characteristics of the materials and… read more here.
Keywords: cad cam; chairside; labside polishing; cam materials ... See more keywords
Evaluation of radiopacities of CAD/CAM restorative materials and resin cements by digital radiography.
Sign Up to like & getrecommendations! Published in 2021 at "Clinical oral investigations"
DOI: 10.1007/s00784-021-03875-y
Abstract: OBJECTIVE This study aims to compare the radiopacities of computer-aided design/computer-aided manufacture (CAD/CAM) blocks and the adhesive cements used for their bonding. MATERIALS AND METHODS 1 ± 0.2 mm thick specimens were obtained from six… read more here.
Keywords: radiopacity; cam blocks; cad cam; resin cements ... See more keywords
Comparative analysis of leaching residual monomer and biological effects of four types of conventional and CAD/CAM dental polymers: an in vitro study.
Sign Up to like & getrecommendations! Published in 2022 at "Clinical oral investigations"
DOI: 10.1007/s00784-021-04271-2
Abstract: OBJECTIVES The objective of this study is to investigate leaching residual monomer and biological effects of four types of conventional and computer-aided design/computer-aided manufacturing (CAD/CAM) dental polymers on human gingival fibroblasts (HGFs). MATERIALS AND METHODS… read more here.
Keywords: cam; residual monomer; dental polymers; cam dental ... See more keywords
Effect of repeated millings on the surface integrity of diamond burs and roughness of different CAD/CAM materials.
Sign Up to like & getrecommendations! Published in 2022 at "Clinical oral investigations"
DOI: 10.1007/s00784-022-04500-2
Abstract: OBJECTIVES This study evaluated the surface integrity of two types of diamond burs and their effect on the roughness of different CAD/CAM materials. MATERIALS AND METHODS CAD/CAM materials, Vita Mark II (VM), IPS e.max CAD… read more here.
Keywords: roughness; surface integrity; cad cam;
Comparison of the different retention appliances produced using CAD/CAM and conventional methods and different surface roughening methods
Sign Up to like & getrecommendations! Published in 2019 at "Lasers in Medical Science"
DOI: 10.1007/s10103-018-2585-7
Abstract: The purposes of this study are to conduct an in vitro comparison of the shear bond strength, breakage mode, and wire deformation of three different types of retainers and to compare the subsequent enamel surface… read more here.
Keywords: enamel surface; surface; wire; deformation ... See more keywords
Complex Parts Partitioning by Elementary Geometric Objects Clustering in CAD/CAM Process
Sign Up to like & getrecommendations! Published in 2019 at "Journal of The Institution of Engineers (India): Series C"
DOI: 10.1007/s40032-019-00528-8
Abstract: Complex shaped parts are omnipresent in the industry: aeronautics, molds, etc. CAD/CAM software is used in their production process. To simulate this process, three geometric representation models can be considered: workpiece model, tool model and… read more here.
Keywords: complex parts; process; model; parts partitioning ... See more keywords
Memotain: A CAD/CAM nickel‐titanium lingual retainer
Sign Up to like & getrecommendations! Published in 2017 at "American Journal of Orthodontics and Dentofacial Orthopedics"
DOI: 10.1016/j.ajodo.2016.11.021
Abstract: &NA; Approximately 1/2 of maxillary and 1/5 of mandibular multi‐stranded lingual retainers fail during retention in some form, either bond failure or wire breakage. Memotain is a new CAD/CAM fabricated lingual retainer wire made of… read more here.
Keywords: cad cam; retainer; nickel titanium; lingual retainer ... See more keywords
Surface quality of yttria-stabilized tetragonal zirconia polycrystal in CAD/CAM milling, sintering, polishing and sandblasting processes.
Sign Up to like & getrecommendations! Published in 2017 at "Journal of the mechanical behavior of biomedical materials"
DOI: 10.1016/j.jmbbm.2016.08.021
Abstract: This paper studied the surface quality (damage, morphology, and phase transformation) of yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) in CAD/CAM milling, and subsequent polishing, sintering and sandblasting processes applied in dental restorations. X-ray diffraction and scanning… read more here.
Keywords: surface quality; surface; cad cam; cam milling ... See more keywords