Evaluation of the Clamping Force of Bolted Joints Using Local Mode Characteristics of a Bolt Head
Sign Up to like & getrecommendations! Published in 2018 at "Journal of Nondestructive Evaluation"
DOI: 10.1007/s10921-018-0528-7
Abstract: It is important to determine and control the clamping force of a bolted joint. Due to its simple setup, the torque control method is typically used to control the clamping force when tightening bolts. After… read more here.
Keywords: bolt head; local mode; control; force bolted ... See more keywords
A novel clamping force searching method based on sensing tie-bar elongation for injection molding
Sign Up to like & getrecommendations! Published in 2017 at "International Journal of Heat and Mass Transfer"
DOI: 10.1016/j.ijheatmasstransfer.2017.02.004
Abstract: Abstract Clamping force greatly influences the injection molding quality, particularly in molding thin-walled plastic parts. Low clamping on mold halves can easily cause flash defects in the part geometry, whereas high clamping can cause poor… read more here.
Keywords: injection molding; force; clamping force; tie bar ... See more keywords
Effect of clamping force on distortion of the optical surface of monochromators during assembly
Sign Up to like & getrecommendations! Published in 2022 at "Journal of Synchrotron Radiation"
DOI: 10.1107/s1600577522003149
Abstract: This work demonstrates the effects of clamping force on the optical surface of a monochromator silicon crystal through the use of finite-element analysis. read more here.
Keywords: optical surface; clamping force; effect clamping; force distortion ... See more keywords
In-Situ Estimation of Bolt Clamping Force by Utilization of Its Effects on Flexural Vibration Propagation
Sign Up to like & getrecommendations! Published in 2023 at "IEEE Access"
DOI: 10.1109/access.2023.3241361
Abstract: After a bolt assembling process, non-destructive identification of the clamping force is important to minimize unexpected failure of the assembled joint structures. For in-situ inspection for every parts, a detachable device which allows generation and… read more here.
Keywords: vibration propagation; vibration; clamping force; situ estimation ... See more keywords
Study on ADRC Parameter Optimization Using CPSO for Clamping Force Control System
Sign Up to like & getrecommendations! Published in 2018 at "Mathematical Problems in Engineering"
DOI: 10.1155/2018/2159274
Abstract: Clamping force control system is essential for clamping tasks that require high precision. In this paper, Active Disturbance Rejection Controller (ADRC) is applied for clamping force control system, aiming to achieve higher control precision. Furthermore,… read more here.
Keywords: adrc; system; force control; control ... See more keywords
Clamping force integrated computer aided tolerancing in composite assembly
Sign Up to like & getrecommendations! Published in 2020 at "Journal of Composite Materials"
DOI: 10.1177/0021998320971027
Abstract: Traditional computer aided tolerancing method could not accomplish the tolerancing and variation simulation well in composite assembly. The paper presents a clamping force integrated computer aided tolerancing method for composite assembly. The stochastic variations and… read more here.
Keywords: composite assembly; clamping force; aided tolerancing; computer aided ... See more keywords
Clamping-force induced birefringence in a single-mode fiber in commercial V-grooves investigated with distributed polarization analysis.
Sign Up to like & getrecommendations! Published in 2022 at "Optics express"
DOI: 10.1364/oe.452756
Abstract: V-grooves are critical components for attaching fiber pigtails to photonics integrated circuits and for holding fibers in optical devices. Improper choice of V-groove angles and clamping method may cause large birefringence in the fibers and… read more here.
Keywords: induced birefringence; force induced; clamping force; birefringence single ... See more keywords
Clamping-force induced birefringence in a single-mode fiber in commercial V-grooves investigated with distributed polarization analysis: erratum.
Sign Up to like & getrecommendations! Published in 2022 at "Optics express"
DOI: 10.1364/oe.460501
Abstract: We correct several errors in our publication [Opt. Express30(4): 5347 (2022)10.1364/OE.452756]. read more here.
Keywords: force induced; birefringence single; induced birefringence; single mode ... See more keywords
Intelligent Predicting of Product Quality of Injection Molding Recycled Materials Based on Tie-Bar Elongation
Sign Up to like & getrecommendations! Published in 2022 at "Polymers"
DOI: 10.3390/polym14040679
Abstract: In the process of injection molding, a certain percentage of recycled material is usually used in order to save costs. The material properties of recycled materials can change significantly compared with raw materials, and the… read more here.
Keywords: injection; quality; clamping force; variation ... See more keywords