Mechanical, interfacial, and fracture characteristics of poly (lactic acid) and Moringa oleifera fiber composites
Sign Up to like & getrecommendations! Published in 2018 at "Advances in Polymer Technology"
DOI: 10.1002/adv.21823
Abstract: Three different processing techniques, extrusion, injection, and compression, were followed to fabricate poly (lactic acid) (PLA) and Moringa oleifera fiber (MOF) based composites. Chopped fibers of length 3–5 mm were used for the extrusion followed… read more here.
Keywords: oleifera fiber; compression; poly lactic; moringa oleifera ... See more keywords
Boron‐polymer composites engineered for compression molding, foaming, and additive manufacturing
Sign Up to like & getrecommendations! Published in 2024 at "Journal of Applied Polymer Science"
DOI: 10.1002/app.55236
Abstract: Boron (specifically 10B) is the element of choice to shield thermal neutrons due to its large (n, α) cross‐section; however, very few polymer composites containing high boron concentrations are available. This study aimed to determine… read more here.
Keywords: compression molding; additive manufacturing; boron; polymer composites ... See more keywords
Taguchi–gray relational analysis of eccentricity and tilt of multilens module mount fabricated by injection compression molding
Sign Up to like & getrecommendations! Published in 2024 at "Polymers for Advanced Technologies"
DOI: 10.1002/pat.6391
Abstract: This study utilizes the mold flow analysis technique of the injection compression molding (ICM) process, combined with the Taguchi–gray relational analysis (GRA), for process optimization analysis on the roundness of the lens holes and the… read more here.
Keywords: mount; compression molding; roundness; taguchi gray ... See more keywords
Compression molding of Carbon/Polyether ether ketone composites: Squeeze flow behavior of unidirectional and randomly oriented strands
Sign Up to like & getrecommendations! Published in 2017 at "Polymer Composites"
DOI: 10.1002/pc.23753
Abstract: Compression molding of randomly oriented strands (ROS) of thermoplastic composite is a new process that enabled the formation of complex shapes with high fiber volume fraction. During compression molding of ROS, several deformation mechanisms occurred.… read more here.
Keywords: squeeze flow; compression molding; randomly oriented; oriented strands ... See more keywords
Compression Molding and Novel Sintering Treatments for Alnico Type-8 Permanent Magnets in Near-Final Shape with Preferred Orientation
Sign Up to like & getrecommendations! Published in 2017 at "JOM"
DOI: 10.1007/s11837-017-2453-0
Abstract: AbstractEconomic uncertainty in the rare earth (RE) permanent magnet marketplace, as well as in an expanding electric drive vehicle market that favors permanent magnet alternating current synchronous drive motors, motivated renewed research in RE-free permanent… read more here.
Keywords: near final; compression molding; permanent magnets; final shape ... See more keywords
Cold Compression Molding of Pyrolytic Carbon from Tires for Oil Absorbers
Sign Up to like & getrecommendations! Published in 2020 at "Procedia Manufacturing"
DOI: 10.1016/j.promfg.2020.04.246
Abstract: Abstract Circular Economy and Environment Management can be strictly connected by integrating latest technologies for material recycling. Project Tyrecs (Tyre Recycling for Clean Seas) aims to produce smart devices for sea cleaning by using recycled… read more here.
Keywords: compression; cold compression; pyrolytic carbon; compression molding ... See more keywords
Fabrication of antimicrobial polymeric films by compression molding of peptide assemblies and polyethylene.
Sign Up to like & getrecommendations! Published in 2022 at "Chemical communications"
DOI: 10.1039/d2cc03018g
Abstract: This paper presents compression molding of peptide assemblies with low-density polyethylene (LDPE) for the robust production of antimicrobial polymeric films. These films show a significant reduction of colony-forming units and plaque-forming units. Moreover, they significantly… read more here.
Keywords: polymeric films; peptide assemblies; molding peptide; antimicrobial polymeric ... See more keywords
Preparation of superhydrophobic nanowires on polypropylene surface via injection compression molding for efficient fog collection
Sign Up to like & getrecommendations! Published in 2024 at "RSC Advances"
DOI: 10.1039/d4ra05074f
Abstract: In this work, a superhydrophobic polypropylene (PP) replica with nanowires is fabricated using an injection compression molding (ICM) process. The morphology, superhydrophobicity and fog water harvesting efficiency of the as-prepared PP replica surface are investigated.… read more here.
Keywords: replica surface; injection compression; compression molding; surface ... See more keywords
Chemical and biology aging of novel green membranes made of PVA and wood flour fibers reinforced with nanosilica manufactured by compression molding process
Sign Up to like & getrecommendations! Published in 2017 at "International Journal of Polymer Analysis and Characterization"
DOI: 10.1080/1023666x.2017.1404271
Abstract: ABSTRACT The purpose of this work was to improve the biodegradable properties of polyvinyl alcohol (PVA)/nanowood flour membranes consisting of nanosilica which were manufactured by compression molding process. Cross-linking of PVA was used to improve… read more here.
Keywords: transient membranes; compression molding; nanosilica manufactured; molding process ... See more keywords
Fabrication of anti-reflective structure array on chalcogenide glass by compression molding with polydimethylsiloxane mold
Sign Up to like & getrecommendations! Published in 2023 at "Optical Engineering"
DOI: 10.1117/1.oe.62.4.045104
Abstract: Abstract. The feasibility of the proposed new process chain was demonstrated by generating an anti-reflective (AR) structure array with continuous profile on a chalcogenide glass substrate. First, a soft mold made of polydimethylsiloxane (PDMS) was… read more here.
Keywords: structure array; compression molding; pdms; glass ... See more keywords
Viscosity characterization of uncured rubber compounds via uniaxial compression testing: Implications for compression molding applications
Sign Up to like & getrecommendations! Published in 2025 at "Journal of Rheology"
DOI: 10.1122/8.0000987
Abstract: This article examines the viscosity measurement of uncured rubber compounds using a simple compression test, with application to compression molding (CM) simulations. Since the nature of the local flow in the compression molding is analogous… read more here.
Keywords: rubber compounds; uncured rubber; compression molding; shear rate ... See more keywords