Electrical and thermal phenomena in low‐density polyethylene/carbon black composites near the percolation threshold
Sign Up to like & getrecommendations! Published in 2019 at "Journal of Applied Polymer Science"
DOI: 10.1002/app.47043
Abstract: Low-density polyethylene (LDPE)/carbon black (CB) composites were fabricated via meltcompounding technique. The percolation threshold was found to be around 20 wt% CB, and an electrical network formed by conductive CB was proven by SEM investigation.… read more here.
Keywords: density polyethylene; percolation; low density; carbon black ... See more keywords
Computational analysis of atomic binding energy for organosilicon‐low‐density polyethylene‐coated silica embedded in polyvinylidene fluoride composite membrane for membrane gas absorption
Sign Up to like & getrecommendations! Published in 2021 at "International Journal of Energy Research"
DOI: 10.1002/er.6810
Abstract: In an effort to enhance the wetting resistance and chemical stability of membrane contactors, silica nanoparticles (SiNP) have been incorporated into polyvinylidene fluoride (PVDF) membrane. These SiNP have been hydrophobically functionalized with three separate organosilicons… read more here.
Keywords: energy; polyvinylidene fluoride; membrane; low density ... See more keywords
Rotational molding of self‐hybrid composites based on linear low‐density polyethylene and maple fibers
Sign Up to like & getrecommendations! Published in 2018 at "Polymer Composites"
DOI: 10.1002/pc.24473
Abstract: In this study, the morphological, physical, and mechanical properties of maple fiber self-hybrid composites reinforced linear low-density polyethylene (LLDPE) have been investigated for different concentration (10, 20, and 30%) and ratio (100/0, 75/25, 50/50, 25/75,… read more here.
Keywords: density polyethylene; linear low; self hybrid; low density ... See more keywords
Multiple shape memory effects of trans‐1,4‐polyisoprene and low‐density polyethylene blends
Sign Up to like & getrecommendations! Published in 2017 at "Polymer International"
DOI: 10.1002/pi.5387
Abstract: A novel series of shape memory blends of trans-1,4-polyisoprene (TPI) and low-density polyethylene (LDPE) were prepared using a simple physical blending method. The mechanical, thermal and shape memory properties of the blends were studied and… read more here.
Keywords: shape; density polyethylene; shape memory; low density ... See more keywords
Rheology–morphology interrelationship in high-density polyethylene/polyamide-6 microfibrillar composites
Sign Up to like & getrecommendations! Published in 2020 at "Polymer Bulletin"
DOI: 10.1007/s00289-020-03446-3
Abstract: Due to the importance of rheology and morphology of microfibrillar reinforced composites (MFCs), a study has been conducted on MFCs based on high-density polyethylene (HDPE) and polyamide-6 (PA-6) using scanning electron microscope and dynamic rheometer.… read more here.
Keywords: high density; density polyethylene; rheology; morphology ... See more keywords
Mechanical and water kinetic parameters of water-absorbed hard wood dust/high-density polyethylene composites
Sign Up to like & getrecommendations! Published in 2020 at "Polymer Bulletin"
DOI: 10.1007/s00289-020-03496-7
Abstract: The mechanical (flexural, tensile and impact) properties and water kinetic parameters of water-absorbed hard wood (mangrove) reinforced high-density polyethylene composites were evaluated as untreated and treated mangrove dust (MD). Samples were prepared by mixing high-density… read more here.
Keywords: water; water absorbed; high density; density polyethylene ... See more keywords
Pyrolysis of low-density polyethylene waste plastics using mixtures of catalysts
Sign Up to like & getrecommendations! Published in 2020 at "Journal of Material Cycles and Waste Management"
DOI: 10.1007/s10163-020-01028-z
Abstract: In the present paper, LDPE has been pyrolysed in a 1 m length semi pilot reactor at temperature range 550–650 °C for around 2 h. Commercial bentonite, kaoline, silica Gel and activated charcoal have been used as catalyst.… read more here.
Keywords: pyrolysis low; polyethylene waste; plastics using; density polyethylene ... See more keywords
Diesel-induced transparency of plastically deformed high-density polyethylene
Sign Up to like & getrecommendations! Published in 2019 at "Journal of Materials Science"
DOI: 10.1007/s10853-019-03700-8
Abstract: High-density polyethylene becomes optically transparent during tensile drawing when previously saturated with diesel fuel. This unusual phenomenon is investigated as it might allow conclusions with respect to the material behavior. Microscopy, differential scanning calorimetry, density… read more here.
Keywords: diesel; high density; density polyethylene; density ... See more keywords
Thermocatalytic Degradation of High Density Polyethylene into Liquid Product
Sign Up to like & getrecommendations! Published in 2017 at "Journal of Polymers and the Environment"
DOI: 10.1007/s10924-017-1088-0
Abstract: Thermocatalytic degradation of high density polyethylene (HDPE) was carried out using acid activated fire clay catalyst in a semi batch reactor. Thermal pyrolysis was performed in the temperature range of 420–500 °C. The liquid and gaseous… read more here.
Keywords: pyrolysis; high density; density polyethylene; thermocatalytic degradation ... See more keywords
Chain structure comparison of two low density polyethylene resins fractionated by temperature rising elution fractionation and thermal fractionation
Sign Up to like & getrecommendations! Published in 2019 at "Journal of Polymer Research"
DOI: 10.1007/s10965-019-1715-7
Abstract: Two low-density polyethylene resins were fractionated into 11 fractions using the temperature rising elution fractionation technique. The resins were of injection molding grade with similar densities but different melt indexes and mechanical properties. High-temperature gel… read more here.
Keywords: two low; chain; temperature; fractionation ... See more keywords
Structural and thermal degradation behaviour of reclaimed clay nano-reinforced low-density polyethylene nanocomposites
Sign Up to like & getrecommendations! Published in 2019 at "Journal of Polymer Research"
DOI: 10.1007/s10965-019-1802-9
Abstract: In this study, a novel reclaimed clay nanofiller was used to manufacture low-density polyethylene (LDPE)/Oil based mud filler (OBMF) nanocomposites by a melt compounding process. The mechanical testing samples were manufactured using injection moulding. The… read more here.
Keywords: low density; reclaimed clay; density polyethylene; structural thermal ... See more keywords