Effect of deposition rate on microstructure and mechanical properties of wire arc additive manufacturing of Ti-6Al-4V components
Sign Up to like & getrecommendations! Published in 2021 at "Journal of Central South University"
DOI: 10.1007/s11771-021-4683-0
Abstract: Wire arc additive manufacturing (WAAM) is a novel manufacturing technique by which high strength metal components can be fabricated layer by layer using an electric arc as the heat source and metal wire as feedstock,… read more here.
Keywords: manufacturing; microstructure; rate; additive manufacturing ... See more keywords
The deposition characteristics of micron particles in heat exchange pipelines
Sign Up to like & getrecommendations! Published in 2019 at "Applied Thermal Engineering"
DOI: 10.1016/j.applthermaleng.2019.113732
Abstract: Abstract Comprehensive understanding of particles deposition in heat exchange pipelines is significant for environment and energy engineering applications. In this study, a numerical simulation method was used to investigate the deposition characteristics of micron particles… read more here.
Keywords: heat exchange; deposition; exchange pipelines; deposition rate ... See more keywords
Increase in silicon film deposition rate in a SiHCl 3 -SiH x -H 2 system
Sign Up to like & getrecommendations! Published in 2017 at "Journal of Crystal Growth"
DOI: 10.1016/j.jcrysgro.2016.10.035
Abstract: Abstract The silicon film deposition rate at 850 °C using trichlorosilane gas was increased by adding SiH x gas which was in situ produced by the thermal decomposition of monomethylsilane gas in ambient hydrogen. With the… read more here.
Keywords: deposition rate; gas; silicon film;
Study of silicon nitride deposition in III-N MOVPE reactors
Sign Up to like & getrecommendations! Published in 2020 at "Journal of Crystal Growth"
DOI: 10.1016/j.jcrysgro.2020.125906
Abstract: Abstract Si3N4 deposition from silane and ammonia in a number of III-N MOVPE reactors of various sizes was studied in a wide range of reactor conditions. It was revealed that Si3N4 deposition rate depends on… read more here.
Keywords: deposition; deposition rate; carrier gas;
The dendrite growth, morphology control and deposition properties of uranium electrorefining
Sign Up to like & getrecommendations! Published in 2021 at "Journal of Nuclear Materials"
DOI: 10.1016/j.jnucmat.2021.153110
Abstract: Abstract In the widely researched and demonstrated molten salt-based electrorefining process, it is extremely important to control the morphology and growth of uranium dendritic in order to guide the design, operation, safeguard and even upgrade… read more here.
Keywords: growth; growth rate; dendrite growth; rate ... See more keywords
Deposition rates and 14C apparent ages of Holocene sediments in the Bothnian Bay of the Gulf of Bothnia using paleomagnetic dating as a reference
Sign Up to like & getrecommendations! Published in 2017 at "Marine Geology"
DOI: 10.1016/j.margeo.2016.10.009
Abstract: Abstract Three 6-m-long cores of sediments were collected in the northern, middle and southern part of the Bothnian Bay. The sediments were dated by paleomagnetic dating techniques, constrained by magnetic properties and geochemical data. The… read more here.
Keywords: bay; bothnian bay; deposition; deposition rate ... See more keywords
Effect of initial particle deposition rate on cake formation during dead-end microfiltration
Sign Up to like & getrecommendations! Published in 2021 at "Journal of Membrane Science"
DOI: 10.1016/j.memsci.2020.118672
Abstract: Abstract The relationships between various parameters and membrane fouling are generally well-established in microfiltration. Surprisingly, a non-monotonic correlation between initial particle deposition rate and extent of flux decline was observed during dead-end microfiltration. To understand… read more here.
Keywords: deposition; microfiltration; particle; deposition rate ... See more keywords
External magnetic field increases both plasma generation and deposition rate in HiPIMS
Sign Up to like & getrecommendations! Published in 2018 at "Surface and Coatings Technology"
DOI: 10.1016/j.surfcoat.2018.02.076
Abstract: Abstract A widely recognised limitation of high power impulse magnetron sputtering (HiPIMS) is the lower deposition rate compared to that achieved using conventional DC sputtering. The HiPIMS deposition rate can be significantly increased by the… read more here.
Keywords: deposition; magnetic field; external magnetic; deposition rate ... See more keywords
Enhancement of discharge and deposition rate in dual-pulse pulsed magnetron sputtering: Effect of ignition pulse width
Sign Up to like & getrecommendations! Published in 2019 at "Surface and Coatings Technology"
DOI: 10.1016/j.surfcoat.2019.06.016
Abstract: Abstract To increase deposition rate during pulsed magnetron sputtering (PMS), a novel dual-pulse pulsed magnetron sputtering (DP-PMS) was proposed. The discharge mode of DP-PMS firstly produced a pulsed high ignition voltage with short duration followed… read more here.
Keywords: ignition pulse; pulse; ignition; deposition rate ... See more keywords
Effect of deposition rate and NNN interactions on adatoms mobility in epitaxial growth
Sign Up to like & getrecommendations! Published in 2017 at "Surface Science"
DOI: 10.1016/j.susc.2017.03.001
Abstract: Abstract This paper provides a detailed analysis of the surface diffusion problem during epitaxial step-flow growth using a simple theoretical model for the diffusion equation of adatoms concentration. Within this framework, an analytical expression for… read more here.
Keywords: mobility; nnn interactions; deposition rate; adatoms mobility ... See more keywords
The effect of deposition rate on amorphous forming composition range and resistivity of Al100−xMox alloy films
Sign Up to like & getrecommendations! Published in 2020 at "Thin Solid Films"
DOI: 10.1016/j.tsf.2020.138354
Abstract: Abstract Amorphous alloy films have much potential for application in many fields. However, their preparation suffers from a disadvantage that the amorphous forming composition range (AFCR) of alloy system is narrow. This study explored a… read more here.
Keywords: range; alloy films; deposition; deposition rate ... See more keywords