LAUSR

About LAUSR
Donate
Contact Us

Follow us:

You are not signed in:

Sign Up!


   Articles with "end milling" as a keyword



Photo from wikipedia

Machine learning-based instantaneous cutting force model for end milling operation

Sign Up to like & get
recommendations! Published in 2020 at "Journal of Intelligent Manufacturing"

DOI: 10.1007/s10845-019-01514-8

Abstract: Cutting force is the fundamental parameter determining the productivity and quality of the milling operation. The development of a generic cutting force model for end milling operation necessitates a large number of experiments. The experimental… read more here.

Keywords: milling operation; force; force model; end milling ... See more keywords
Photo by taylorheeryphoto from unsplash

Design of the Ceramic-Bladed End Milling Cutters with Regard for Their Stress-Strain State for the Innovation Technological Processes. Choice of Ceramics. Part 1

Sign Up to like & get
recommendations! Published in 2019 at "Refractories and Industrial Ceramics"

DOI: 10.1007/s11148-019-00272-7

Abstract: We show the applicability of the method of designing ceramic tools based on the analysis of their stress-strain state in the choice of ceramics used for the creation of ceramic end milling cutters. We present… read more here.

Keywords: strain state; milling cutters; choice ceramics; end milling ... See more keywords
Photo from archive.org

Spark Plasma Sintering of Al2O3-Ceramic Workpieces for Small End Milling Cutters

Sign Up to like & get
recommendations! Published in 2019 at "Refractories and Industrial Ceramics"

DOI: 10.1007/s11148-019-00285-2

Abstract: Features of the effect of sintering temperature, pressure and duration of isothermal exposure during spark plasma sintering on the structure of Al2O3 ceramics without activating additives are determined. The correlation revealed makes it possible to… read more here.

Keywords: small end; plasma sintering; milling cutters; spark plasma ... See more keywords
Photo by shapelined from unsplash

Tribological Behavior of Multi-scaled Patterned Surfaces Machined Through Inclined End Milling and Micro Shot Blasting

Sign Up to like & get
recommendations! Published in 2018 at "Tribology Letters"

DOI: 10.1007/s11249-018-1086-y

Abstract: Surface texturing is one mechanism that friction coefficients in both dry and lubricated contacts can be reduced compared with untextured, flat surfaces. End milling and shot blasting are two processes used to produce surface textures,… read more here.

Keywords: surface texturing; surface; friction; coefficient ... See more keywords
Photo from wikipedia

Process design for 5-axis ball end milling using a real-time capable dynamic material removal simulation

Sign Up to like & get
recommendations! Published in 2020 at "Production Engineering"

DOI: 10.1007/s11740-020-01003-5

Abstract: For repairing turbine blades or die and mold forms, additive manufacturing processes are commonly used to build-up new material to damaged sections. Afterwards, a subsequent re-contouring process such as 5-axis ball end milling is required… read more here.

Keywords: process; material; axis ball; simulation ... See more keywords
Photo from wikipedia

Experimental and theoretical investigation on cutting forces in off-centre micro ball end milling

Sign Up to like & get
recommendations! Published in 2018 at "CIRP Journal of Manufacturing Science and Technology"

DOI: 10.1016/j.cirpj.2018.07.003

Abstract: Abstract Free-form surfaces and micro features are finish machined by a micro ball end mill by removing steps left behind by flat end mill in the previous operation. For effective machining, off-centre ball end milling… read more here.

Keywords: micro ball; forces centre; end; end mill ... See more keywords
Photo by joshua_hoehne from unsplash

3D surface topography simulation and experiments for ball-end NC milling considering dynamic feedrate

Sign Up to like & get
recommendations! Published in 2020 at "Cirp Journal of Manufacturing Science and Technology"

DOI: 10.1016/j.cirpj.2020.05.011

Abstract: Abstract Dynamic change of feedrate is almost inevitable in high speed milling along a curved path due to the drive limits of the machine tools. The surface topography caused by the change of feedrate, which… read more here.

Keywords: topography; feedrate; end milling; ball end ... See more keywords
Photo by jordanmcdonald from unsplash

Investigation on the performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of maraging steel under dry, wet and cryogenic environments

Sign Up to like & get
recommendations! Published in 2019 at "Journal of Manufacturing Processes"

DOI: 10.1016/j.jmapro.2019.05.021

Abstract: Abstract The present study investigates the machining performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of MDN 250 maraging steel. The mechanical and metallurgical characterization is carried out to determine the… read more here.

Keywords: end milling; performance alcrn; performance; alcrn altin ... See more keywords
Photo from wikipedia

Optimisation of machining parameters during ball end milling of hardened steel with various surface inclinations

Sign Up to like & get
recommendations! Published in 2017 at "Measurement"

DOI: 10.1016/j.measurement.2017.07.020

Abstract: This paper proposes a method for the reduction of forces and the improvement of efficiency during finish ball end milling of hardened 55NiCrMoV6 steel. The primary objective of this work concentrates on the optimal selection… read more here.

Keywords: surface inclination; surface; milling hardened; end milling ... See more keywords
Photo by priscilladupreez from unsplash

Minimization of cutting force, temperature and surface roughness through GRA, TOPSIS and Taguchi techniques in end milling of Mg hybrid MMC

Sign Up to like & get
recommendations! Published in 2018 at "Measurement"

DOI: 10.1016/j.measurement.2017.11.011

Abstract: Abstract Present study investigates the effect of material and machining parameters on cutting force, surface roughness and temperature in end milling of Magnesium (Mg) Metal Matrix Composite (MMC) using carbide tool. Mg hybrid composite was… read more here.

Keywords: end milling; cutting force; surface roughness; force ... See more keywords
Photo from wikipedia

Study on metrological relations between instant tool displacements and surface roughness during precise ball end milling

Sign Up to like & get
recommendations! Published in 2018 at "Measurement"

DOI: 10.1016/j.measurement.2018.07.058

Abstract: Abstract The study presents an analysis of relations between the instantaneous tool displacements and surface roughness formed during ball end milling of surface with inclination towards the tool’s axis. A novel experimental method for the… read more here.

Keywords: end milling; surface roughness; ball end; tool ... See more keywords