A Comparison Study of the Thermal Fatigue Properties of Three Ni‐Based Cast Superalloys Cycled from 20 to 1100 °C
Sign Up to like & getrecommendations! Published in 2019 at "Advanced Engineering Materials"
DOI: 10.1002/adem.201900054
Abstract: The thermal fatigue properties of cycling from 20 to 1100 °C, a new kind of Ni‐based cast superalloy, named N3 are studied and the results are compared with those of other alloys, namely, K4002 and K403,… read more here.
Keywords: fatigue properties; thermal fatigue; based cast; alloy ... See more keywords
Bending fatigue performance of three‐dimensional woven composites—A review
Sign Up to like & getrecommendations! Published in 2024 at "Polymer Composites"
DOI: 10.1002/pc.28951
Abstract: Three‐dimensional woven composites (3DWCs) are gradually used in marine, transportation, military, and other applications owing to their high interlayer properties, load‐bearing capacity, and good near‐net‐shape forming abilities. 3DWCs are often subjected to bending fatigue loads,… read more here.
Keywords: fatigue; fatigue properties; three dimensional; bending fatigue ... See more keywords
Effect of Etching on Fatigue Properties of DD6 Single-Crystal Superalloy
Sign Up to like & getrecommendations! Published in 2020 at "Journal of Materials Engineering and Performance"
DOI: 10.1007/s11665-020-04865-z
Abstract: The effects of etching on the surface integrities and the high cycle fatigue properties of DD6 single-crystal superalloy were investigated. The standard heat treated DD6 specimens were etched twice and four times using HCl/H 2… read more here.
Keywords: fatigue properties; fatigue; surface; etching fatigue ... See more keywords
Microstructure, Tensile and Fatigue Properties of Al–5 wt.%Mg Alloy Manufactured by Twin Roll Strip Casting
Sign Up to like & getrecommendations! Published in 2018 at "Metals and Materials International"
DOI: 10.1007/s12540-018-0123-6
Abstract: This study investigated the microstructure, tensile and fatigue properties of Al–5 wt.%Mg alloy manufactured by twin roll strip casting. Strips cast as a fabricated (F) specimen and a specimen heat treated (O) at 400 °C/5 h were produced… read more here.
Keywords: properties alloy; fatigue properties; strip; fatigue ... See more keywords
The Impact of HIP Process and Heat Treatment on the Mechanical Behaviour of an Al–Si–Mg Alloy Component
Sign Up to like & getrecommendations! Published in 2024 at "International Journal of Metalcasting"
DOI: 10.1007/s40962-023-01226-z
Abstract: This study investigates the effect of hot isostatic pressing (HIPping) on the static and fatigue properties of sand-casting A356 aluminium alloys. HIPping is a method to improve the fatigue properties in aluminium cast material by… read more here.
Keywords: process; fatigue; hip process; fatigue properties ... See more keywords
Quasi-static and fatigue properties of graded Ti–6Al–4V lattices produced by Laser Powder Bed Fusion (LPBF)
Sign Up to like & getrecommendations! Published in 2020 at "Additive manufacturing"
DOI: 10.1016/j.addma.2020.101653
Abstract: Abstract The additive manufacturing of metallic lattices based on triply periodic minimal surfaces (TPMS) has recently received plenty of interest in the field of hard tissue engineering. Although these structures are deemed to present advantages… read more here.
Keywords: 6al lattices; properties graded; fatigue properties; quasi static ... See more keywords
Effects of cold working and corrosion on fatigue properties and fracture behaviors of precipitate strengthened Cu-Ni-Si alloy
Sign Up to like & getrecommendations! Published in 2018 at "International Journal of Fatigue"
DOI: 10.1016/j.ijfatigue.2018.06.017
Abstract: Abstract In this study, the tensile and fatigue tests were conducted on precipitate strengthened Cu-Ni-Si alloy. The fatigue properties of specimens with cold working and without cold working in air, as well as that of… read more here.
Keywords: fatigue properties; fatigue; precipitate strengthened; cold working ... See more keywords
Improvement of fatigue properties of Ti-6Al-4V alloy under four-point bending by low temperature nitriding
Sign Up to like & getrecommendations! Published in 2019 at "International Journal of Fatigue"
DOI: 10.1016/j.ijfatigue.2018.11.005
Abstract: Abstract Low temperature nitriding (LTN) was performed for titanium alloy (Ti-6Al-4V) to improve its fatigue properties. A nitrogen compound layer was formed on the surface nitrided at temperatures higher than 873 K, whereas nitrogen diffusion was… read more here.
Keywords: fatigue; temperature; low temperature; temperature nitriding ... See more keywords
Compression fatigue properties of open-cell aluminum foams fabricated by space-holder method
Sign Up to like & getrecommendations! Published in 2019 at "International Journal of Fatigue"
DOI: 10.1016/j.ijfatigue.2018.11.008
Abstract: Abstract The compression-compression fatigue properties of open-cell Al foams fabricated by space-holder method with different porosities were investigated. The e–N curves of the Al foams show two types based on the stress levels (k). The… read more here.
Keywords: fatigue; properties open; open cell; compression ... See more keywords
Effect of long period stacking ordered phase on the fatigue properties of extruded Mg-Y-Zn alloys
Sign Up to like & getrecommendations! Published in 2019 at "International Journal of Fatigue"
DOI: 10.1016/j.ijfatigue.2019.105205
Abstract: Abstract The fatigue properties of two Mg-Y-Zn alloys with different amount of long-period stacking order (LPSO) phase, Mg 97 Zn 1 Y 2 and Mg 89 Zn 4 Y 7 , were investigated. Low-cycle fatigue… read more here.
Keywords: fatigue; long period; period stacking; fatigue properties ... See more keywords
Effects of hygrothermal aging and fiber orientations on constant amplitude fatigue properties of CFRP multidirectional composite laminates
Sign Up to like & getrecommendations! Published in 2020 at "International Journal of Fatigue"
DOI: 10.1016/j.ijfatigue.2020.105590
Abstract: Abstract Carbon fiber reinforced polymer (CFRP) multidirectional composite laminates are vital for moisture-prone structures where directional fatigue properties can be optimized. In this work, the tension-tension(T-T) and tension-compression(T-C) fatigue properties of hygrothermal aged [±454]S and… read more here.
Keywords: hygrothermal aging; fatigue properties; multidirectional composite; fatigue ... See more keywords