Sign Up to like & get recommendations! 0
Published in 2018 at "Ceramics International"
DOI: 10.1016/j.ceramint.2018.04.171
Abstract: Abstract Monolithic TiB 2 and TiB 2 –5 wt% Si 3 N 4 ultrahigh temperature ceramics were fabricated by spark plasma sintering (SPS) at 1900 °C for 7 min under 40 MPa. The addition of Si 3 N 4… read more here.
Sign Up to like & get recommendations! 1
Published in 2019 at "International Journal of Refractory Metals and Hard Materials"
DOI: 10.1016/j.ijrmhm.2019.105038
Abstract: Abstract In this study, Ni or Co + Ni bonded NbC matrix cermets with secondary carbides (Mo2C and WC) as well as Ti(C0.5N0.5) were prepared by liquid phase sintering at 1450 °C in vacuum. Detailed microstructural investigation was… read more here.
Sign Up to like & get recommendations! 0
Published in 2018 at "Journal of Alloys and Compounds"
DOI: 10.1016/j.jallcom.2018.05.324
Abstract: Abstract The microstructure evolution of Al-3wt.%Mg reinforced with 10 vol% B4C during isothermal compression at temperatures ranging 300–500 °C at strain rates of 0.001–10 s−1 was investigated by electron backscatter diffraction (EBSD). According to the results, at… read more here.
Sign Up to like & get recommendations! 0
Published in 2019 at "Journal of Alloys and Compounds"
DOI: 10.1016/j.jallcom.2019.03.068
Abstract: Abstract In this research paper the microstructure of the magnesium AZ31B alloy is investigated after the application of a single monotonic compressive strain of −0.4%. A band of twinned grains is observed to form in the… read more here.
Sign Up to like & get recommendations! 2
Published in 2021 at "Materials Characterization"
DOI: 10.1016/j.matchar.2021.111110
Abstract: Abstract We report our findings of a detailed investigation into the frequent failures of ethylene furnace radiant tubes at a petrochemical plant. One of the failed samples having gas tungsten arc welded joint between Kanthal-APMT(Fe-based)… read more here.
Sign Up to like & get recommendations! 0
Published in 2018 at "Journal of Materials Chemistry C"
DOI: 10.1039/c7tc05456d
Abstract: A nanocrystalline iron-rich telluride, Fe5Te4, was prepared mechanochemically using ball milling procedures in an inert atmosphere, starting from FexTe powder mixtures with x = 1.0, 1.25 and 1.5, with x = 1.25 leading to the… read more here.
Sign Up to like & get recommendations! 1
Published in 2022 at "Soft matter"
DOI: 10.1039/d2sm00248e
Abstract: Oil-continuous drilling fluids used in the oil and gas industry are formulated to be pseudoplastic with a relatively weak yield stress. These fluids are required to maintain their properties over wide temperature and pressure ranges… read more here.
Sign Up to like & get recommendations! 1
Published in 2018 at "SPINE"
DOI: 10.1097/brs.0000000000002652
Abstract: Study Design. Microstructural investigation of compression-induced herniation of a lumbar disc held in a concordant complex posture. Objective. To explore the significance of loading rate in a highly asymmetric concordant posture, comparing the mechanisms of… read more here.
Sign Up to like & get recommendations! 0
Published in 2020 at "Energies"
DOI: 10.3390/en13030563
Abstract: A high-energy ball milling and subsequent high-pressure torsion method was applied to synthesize nanocrystalline magnesium samples catalyzed by TiO 2 or titanate nanotubes. The microstructure of the as-milled powders and the torqued bulk disks was… read more here.