Influence of SMAT Parameters on Microstructural and Mechanical Properties of Al-Mg-Si Alloy AA 6061
Sign Up to like & getrecommendations! Published in 2017 at "Journal of Materials Engineering and Performance"
DOI: 10.1007/s11665-017-2612-z
Abstract: In the present work, the influence of surface mechanical attrition treatment (SMAT) parameters on the microstructural and mechanical properties of an aluminum-magnesium-silicon alloy AA 6061 was studied using design of experiment technique. Balls of three… read more here.
Keywords: smat parameters; parameters microstructural; surface; microstructural mechanical ... See more keywords
Microstructural and Mechanical Evaluations of Transient Liquid Phase Bonded In X-750/BNi-3/SAF 2205
Sign Up to like & getrecommendations! Published in 2020 at "Journal of Materials Engineering and Performance"
DOI: 10.1007/s11665-020-04620-4
Abstract: In this study, dissimilar joining between SAF 2205 duplex stainless steel and Inconel X-750 superalloy produced by TLP process was investigated. This process was done at temperature of 1100 °C for different bonding times of… read more here.
Keywords: evaluations transient; microscopy; mechanical evaluations; microstructural mechanical ... See more keywords
Microstructural and Mechanical Properties of TiCX–Ni3(Al,Ti)/Ni Functionally Graded Composites Fabricated from Ti3AlC2 and Ni Powders
Sign Up to like & getrecommendations! Published in 2019 at "Metals and Materials International"
DOI: 10.1007/s12540-019-00357-5
Abstract: Abstract In this paper, a novel type of functionally graded material (FGM) was successfully fabricated from pure Ni and Ti 3 AlC 2 powder mixtures by hot-press sintering route at 1200 °C and 17 MPa. In each… read more here.
Keywords: ni3 functionally; functionally graded; microstructural mechanical; ticx ni3 ... See more keywords
Enhanced microstructural and mechanical properties of Stellite/WC nanocomposite on Inconel 718 deposited through vibration-assisted laser cladding
Sign Up to like & getrecommendations! Published in 2021 at "International Journal of Minerals, Metallurgy and Materials"
DOI: 10.1007/s12613-020-2211-0
Abstract: Stellite-21/WC nanopowders were deposited on Inconel through vibration-assisted laser cladding with different laser parameters. Optical and scanning electron microscopy, hardness measurements, and wear characterizations were employed to understand the microstructural and mechanical behaviors of the… read more here.
Keywords: assisted laser; vibration assisted; enhanced microstructural; microstructural mechanical ... See more keywords
Microstructural, mechanical, and thermal properties of microwave-sintered KLS-1 lunar regolith simulant
Sign Up to like & getrecommendations! Published in 2021 at "Ceramics International"
DOI: 10.1016/j.ceramint.2021.06.098
Abstract: Abstract KLS-1 Lunar regolith simulant was microwave sintered to explore its potential applicability in future lunar construction. The effects of sintering temperature on linear shrinkage, density, porosity, and microstructural, mechanical, and thermal properties were investigated.… read more here.
Keywords: lunar regolith; kls lunar; microstructural mechanical; microwave sintered ... See more keywords
Effect of chemical and thermal activation on the microstructural and mechanical properties of more sustainable UHPC
Sign Up to like & getrecommendations! Published in 2018 at "Construction and Building Materials"
DOI: 10.1016/j.conbuildmat.2018.02.214
Abstract: Abstract This paper investigates the influence of the content of blast furnace slag (BFS) on the microstructural and mechanical properties of non-activated and activated ultra-high performance concrete (UHPC). Three volume-substitution rates of cement with BFS… read more here.
Keywords: microstructural mechanical; chemical thermal; mechanical properties; compressive strength ... See more keywords
Microstructural and mechanical properties of porous Si3N4 carbon coated ceramic brazed with a cobalt-silicon filler
Sign Up to like & getrecommendations! Published in 2017 at "Journal of The European Ceramic Society"
DOI: 10.1016/j.jeurceramsoc.2017.03.031
Abstract: Abstract The Co 22.5 Si 77.5 (at.%) braze was used to bond porous Si 3 N 4 ceramics. The effects of brazing temperature on microstructure and the bonding strength of the joint were studied. The… read more here.
Keywords: strength; microstructural mechanical; carbon coated; joint strength ... See more keywords
Influence of alloying element Zn on the microstructural, mechanical and corrosion properties of binary Mg-Zn alloys after severe plastic deformation
Sign Up to like & getrecommendations! Published in 2017 at "Materials Characterization"
DOI: 10.1016/j.matchar.2017.10.017
Abstract: Abstract This work presents an analysis of the microstructural, mechanical and corrosion properties of two binary Mg-Zn alloys. Mg-6 wt%Zn and Mg-12 wt%Zn cast alloys were subjected to annealing followed by quenching and processed via… read more here.
Keywords: corrosion properties; microstructural mechanical; initial state; corrosion ... See more keywords
Microstructural and Mechanical Behavior in the Al2024 Alloy Modified With Addition of CeO2
Sign Up to like & getrecommendations! Published in 2017 at "Microscopy and Microanalysis"
DOI: 10.1017/s1431927617008911
Abstract: The 2xxx series aluminium alloys are important advanced functional materials due to their high yield strength, good fracture toughness and excellent fatigue properties [1]. Due to the extremely important role that the 2xxx series aluminum… read more here.
Keywords: mechanical behavior; al2024 alloy; behavior al2024; microstructural mechanical ... See more keywords
Microstructural, mechanical and intergranular corrosion behavior of cold work and thermal ageing of low nickel austenitic stainless steel
Sign Up to like & getrecommendations! Published in 2019 at "Materials Research Express"
DOI: 10.1088/2053-1591/aad508
Abstract: In the present investigation, microstructural, mechanical and electrochemical properties of cold rolled Cr-Mn austenitic stainless steel were studied. Heat treatment (800 °C, 900 °C, 950 °C and 1000 °C) and thermal ageing (one, two and… read more here.
Keywords: stainless steel; austenitic stainless; thermal ageing; temperature ... See more keywords
Elucidating the signal for contact guidance contained in aligned fibrils with a microstructural–mechanical model
Sign Up to like & getrecommendations! Published in 2022 at "Journal of the Royal Society Interface"
DOI: 10.1098/rsif.2021.0951
Abstract: Despite its importance in physiological processes and tissue engineering, the mechanism underlying cell contact guidance in an aligned fibrillar network has defied elucidation due to multiple interdependent signals that such a network presents to cells,… read more here.
Keywords: network; contact guidance; mechanical model; microstructural mechanical ... See more keywords