Histopathological evaluation of the R134a multipulsed spray cooling assisted 1210 nm laser lipolysis by the murine model in vivo
Sign Up to like & getrecommendations! Published in 2022 at "Lasers in Surgery and Medicine"
DOI: 10.1002/lsm.23607
Abstract: Owing to the greater absorption affinity for lipo‐rich tissue than water, the 1210 nm laser is a promising candidate for transcutaneous lipolysis in the near‐infrared band. However, fat reduction is limited because laser therapy may yield… read more here.
Keywords: spray cooling; histopathological evaluation; 1210 laser; lipolysis ... See more keywords
Experimental investigation on the performance of a water spray cooling system
Sign Up to like & getrecommendations! Published in 2017 at "Applied Thermal Engineering"
DOI: 10.1016/j.applthermaleng.2016.10.191
Abstract: Abstract In this paper, the performance of a water spray cooling system is investigated experimentally. The influence factors including the nozzle atomization effect, spray height, heat flux, inlet pressure and gravity angle are discussed. Results… read more here.
Keywords: heat transfer; spray; spray cooling; performance ... See more keywords
Experimental study on heat transfer performance of a novel compact spray cooling module
Sign Up to like & getrecommendations! Published in 2019 at "Applied Thermal Engineering"
DOI: 10.1016/j.applthermaleng.2019.03.078
Abstract: Abstract With the rapid increase in power density for miniaturization and integration of electronic component, the liquid-cooled cold plate, shows difficulty in meeting the increasing heat demand of electronic chips. In this paper, a novel… read more here.
Keywords: heat; spray cooling; cooling module; novel compact ... See more keywords
Effects of injection pressure difference on droplet size distribution and spray cone angle in spray cooling of liquid nitrogen
Sign Up to like & getrecommendations! Published in 2017 at "Cryogenics"
DOI: 10.1016/j.cryogenics.2017.01.011
Abstract: Abstract Spray cooling with liquid nitrogen as the working fluid has been widely employed in a plenty of fields requiring cooling at cryogenic temperature, such as the cryogenic wind tunnels and cooling super-conducting magnets. In… read more here.
Keywords: pressure difference; spray cooling; spray; injection pressure ... See more keywords
Enhanced heat transfer by an original immersed spray cooling system integrated with an ejector
Sign Up to like & getrecommendations! Published in 2018 at "Energy"
DOI: 10.1016/j.energy.2018.06.019
Abstract: Abstract Spray cooling is believed to be a promising candidate for the cooling of the next-generation high heat-flux electronics. Different from the traditional spray cooling (SC), a modified version of SC – immersed spray cooling… read more here.
Keywords: immersed spray; spray; system; ejector ... See more keywords
Influence of air on heat transfer of a closed-loop spray cooling system
Sign Up to like & getrecommendations! Published in 2020 at "Experimental Thermal and Fluid Science"
DOI: 10.1016/j.expthermflusci.2019.109903
Abstract: Abstract The influence of air must be considered when designing a direct spray cooling system for electronics because of its inevitable existence. In the present study, the influence of air on spray cooling is experimentally… read more here.
Keywords: system; air; heat transfer; influence ... See more keywords
Thermal management strategy for electronic chips based on combination of a flat-plate heat pipe and spray cooling
Sign Up to like & getrecommendations! Published in 2021 at "International Journal of Heat and Mass Transfer"
DOI: 10.1016/j.ijheatmasstransfer.2021.121894
Abstract: Abstract With the rapid development of electronic technology, the required heat dissipation capacities of electronic chips are increasing. In this study, a thermal management strategy for electronic chips based on a combination of a flat-plate… read more here.
Keywords: heat; spray cooling; heat pipe; temperature ... See more keywords
Numerical investigation on heat transfer of water spray cooling from single-phase to nucleate boiling region
Sign Up to like & getrecommendations! Published in 2020 at "International Journal of Thermal Sciences"
DOI: 10.1016/j.ijthermalsci.2019.106258
Abstract: Abstract In the present study, spray cooling heat transfer characteristics were numerically investigated under the heat flux ranging from 50 to 170 W/cm2. Effect of nozzle height and spray pressure was also studied in order to… read more here.
Keywords: heat; phase; spray cooling; heat transfer ... See more keywords
Synthesis of Cu-Al LDH nanofluid and its application in spray cooling heat transfer of a hot steel plate
Sign Up to like & getrecommendations! Published in 2018 at "Powder Technology"
DOI: 10.1016/j.powtec.2018.05.004
Abstract: Abstract In the current study, authors have synthesized Cu-Al Layered Double Hydroxide nanofluid at different molar ratios of Cu and Al by using co-precipitation technique and utilized this as a coolant in a pressure atomized… read more here.
Keywords: molar ratio; spray; ratio; heat transfer ... See more keywords
Voltage–Current Characteristics and Temperature Variation by DC Power Source for the YBCO Coated Conductor Under Spray Cooling Method
Sign Up to like & getrecommendations! Published in 2019 at "IEEE Transactions on Applied Superconductivity"
DOI: 10.1109/tasc.2019.2908561
Abstract: This paper proposes the spray cooling method in conducting the extremely low temperature cooling of the superconducting wire, and presents the results of cooling performance tests and characteristics of the spray cooling method. To that… read more here.
Keywords: temperature; voltage current; cooling method; spray cooling ... See more keywords
Experimental Investigation on Oil Spray Cooling With Hairpin Windings
Sign Up to like & getrecommendations! Published in 2020 at "IEEE Transactions on Industrial Electronics"
DOI: 10.1109/tie.2019.2942563
Abstract: Hairpin windings are gaining increasing popularity in recent years due to their advantages in improving electrical machine performance while reducing manufacturing time and costs. Their geometrical features introduce new challenges and opportunities on thermal management.… read more here.
Keywords: hairpin windings; spray cooling; oil; cooling hairpin ... See more keywords