Photo from wikipedia
Sign Up to like & get
recommendations!
0
Published in 2018 at "Acta Materialia"
DOI: 10.1016/j.actamat.2018.02.005
Abstract: Abstract The present study systematically investigated the effect of Si additions from 0 to 3 wt.% on the deformation mechanisms of a 0.2C-10Mn-3Al medium Mn steel. Two austenite-ferrite duplex microstructures, characterized by the different austenite characteristics…
read more here.
Keywords:
additions deformation;
ferrite duplex;
austenite ferrite;
effect ... See more keywords
Sign Up to like & get
recommendations!
0
Published in 2019 at "International Journal of Fatigue"
DOI: 10.1016/j.ijfatigue.2019.105218
Abstract: Abstract Three multi-phase steels, all comprising 80% bainite and 20% ferrite have been studied under low cycle fatigue. Under monotonic loading the steels exhibit high strengths (>1 GPa) and reasonable ductilities of 10–20% elongation. Under…
read more here.
Keywords:
fatigue;
strain partitioning;
strain;
phase steels ... See more keywords
Sign Up to like & get
recommendations!
1
Published in 2018 at "Journal of Structural Geology"
DOI: 10.1016/j.jsg.2018.05.016
Abstract: Abstract Partial melts can form as a result of crustal thickening due to orogenesis. Even small melt fractions weaken the crust, so that partially molten volumes should accumulate significant amounts of strain. However, relatively little…
read more here.
Keywords:
crust;
syn melt;
strain;
strain partitioning ... See more keywords
Sign Up to like & get
recommendations!
0
Published in 2020 at "Materialia"
DOI: 10.1016/j.mtla.2020.100619
Abstract: Abstract Observations based on either side of experiment or modeling often have difficulties in understanding microstructural and mechanical evolutions during deformation, and in application to the macroscopic behavior of materials. In the present study, an…
read more here.
Keywords:
ferrous medium;
transformation;
medium entropy;
stress ... See more keywords
Sign Up to like & get
recommendations!
1
Published in 2020 at "Tectonics"
DOI: 10.1029/2019tc005886
Abstract: Strain partitioning onto margin‐parallel thrust and strike‐slip faults is a common process at obliquely convergent plate margins, leading to the formation and migration of crustal slivers. The degree of strain partitioning and rate of sliver…
read more here.
Keywords:
obliquity;
strain partitioning;
angle;
zone ... See more keywords
Sign Up to like & get
recommendations!
0
Published in 2018 at "Materials Research Letters"
DOI: 10.1080/21663831.2018.1439115
Abstract: ABSTRACT Deformation behavior of a harmonic structured material (HSM), core–shell 304L stainless steel, is investigated using micro-digital image correlation (micro-DIC). High strain-partitioning between core and shell is observed. Because the grain boundaries with a grain-size…
read more here.
Keywords:
back stress;
core shell;
strain partitioning;
harmonic structured ... See more keywords
Sign Up to like & get
recommendations!
0
Published in 2018 at "Basin Research"
DOI: 10.1111/bre.12253
Abstract: Spatio-temporal analysis of basins formed along sheared margins has received much less attention than those formed along orthogonally extended margins. Knowledge about the structural evolution of such basins is important for petroleum exploration but there…
read more here.
Keywords:
norwegian barents;
structural evolution;
strain partitioning;
basin ... See more keywords
Photo from wikipedia
Sign Up to like & get
recommendations!
0
Published in 2020 at "Solid Earth"
DOI: 10.5194/se-11-935-2020
Abstract: Abstract. Normal faults have irregular geometries on a range of scales arising from different processes including refraction and segmentation. A fault with constant dip and displacement on a large-scale will have irregular geometries on smaller…
read more here.
Keywords:
strain partitioning;
fault bend;
normal faults;
bend folding ... See more keywords