Photo from wikipedia
Sign Up to like & get
recommendations!
1
Published in 2021 at "Advanced Engineering Materials"
DOI: 10.1002/adem.202100049
Abstract: As a representative of a common carbon‐bearing hot work tool steel AISI H13 is in focus of the present review paper. Most relevant details for processing of AISI H13 by laser powder bed fusion (L‐PBF)…
read more here.
Keywords:
tool steel;
hot work;
aisi h13;
work tool ... See more keywords
Photo from wikipedia
Sign Up to like & get
recommendations!
1
Published in 2018 at "Journal of Materials Engineering and Performance"
DOI: 10.1007/s11665-018-3669-z
Abstract: Pulsed plasma nitriding and post-oxidizing process have been applied to hot work H13 tool steel to enhance the tribological properties (friction coefficient and wear rate). Nitriding was accomplished under specific conditions to generate a free…
read more here.
Keywords:
h13 tool;
treatment;
plasma nitriding;
tool steel ... See more keywords
Photo from wikipedia
Sign Up to like & get
recommendations!
0
Published in 2018 at "JOM"
DOI: 10.1007/s11837-018-2991-0
Abstract: An H13 (high-strength, low-ductility) tool steel die will fail due to compressive high cycle fatigue. If the die is manufactured by direct metal deposition and layered with Inconel-718 (low-strength, high-ductility), it may impact the mechanical…
read more here.
Keywords:
additive manufactured;
strength;
inconel 718;
tool steel ... See more keywords
Photo from wikipedia
Sign Up to like & get
recommendations!
1
Published in 2018 at "Metals and Materials International"
DOI: 10.1007/s12540-018-00220-z
Abstract: The microstructure distribution and distortion behavior of a cold work tool steel cylindrical specimen with keyway after quenching (QT) and deep cryogenic treatment (DCT) were evaluated in detail. Furthermore, from the viewpoints of thermal and…
read more here.
Keywords:
work tool;
distortion;
quenching deep;
tool steel ... See more keywords
Photo from wikipedia
Sign Up to like & get
recommendations!
1
Published in 2018 at "Metals and Materials International"
DOI: 10.1007/s12540-018-0138-z
Abstract: Dilatometry is a useful technique to obtain experimental data concerning transformation. In this paper, a dilation conversional model was established to calculate carbides fraction in AISI H13 hot-work tool steel based on the measured length…
read more here.
Keywords:
work tool;
tool steel;
hot work;
model ... See more keywords
Photo by nci from unsplash
Sign Up to like & get
recommendations!
1
Published in 2018 at "Arabian Journal for Science and Engineering"
DOI: 10.1007/s13369-018-3242-y
Abstract: The present research paper focuses on optimisation of wear test parameters for different deep cryogenic treated AISI M2 tool steel material. Commercially available, AISI M2 tool steel material is machined as per ASTM G99-05 standards…
read more here.
Keywords:
tool steel;
cryogenic treatment;
deep cryogenic;
aisi tool ... See more keywords
Photo from wikipedia
Sign Up to like & get
recommendations!
1
Published in 2021 at "Arabian Journal for Science and Engineering"
DOI: 10.1007/s13369-020-05156-4
Abstract: This paper investigates the effects on the electrical discharge machining (EDM) characteristics of SKD 11 cold work tool steel when adding graphite (Gr) and boron carbide (B4C) powder to the dielectric fluid. The introduction of…
read more here.
Keywords:
boron carbide;
electrical discharge;
graphite boron;
tool steel ... See more keywords
Sign Up to like & get
recommendations!
1
Published in 2019 at "Journal of Bio- and Tribo-Corrosion"
DOI: 10.1007/s40735-019-0238-4
Abstract: Rock drilling performance of O1 tool steel was simulated at laboratory scale using mortar specimens. Mortar specimens were prepared with cement-to-sand ratio of 1:2 and cured for 7 and 30 days to simulate soft and hard…
read more here.
Keywords:
performance tool;
tool;
tribocorrosion;
tool steel ... See more keywords
Photo from wikipedia
Sign Up to like & get
recommendations!
1
Published in 2017 at "Applied Surface Science"
DOI: 10.1016/j.apsusc.2016.11.164
Abstract: Abstract Titanium carbide (TiC) reinforced tool steel matrix composites were successfully fabricated by a liquid pressing infiltration process and research was subsequently conducted to investigate the composites’ oxidation resistance. The mass gain of the tested…
read more here.
Keywords:
oxidation resistance;
surface;
tool steel;
oxidation ... See more keywords
Sign Up to like & get
recommendations!
0
Published in 2018 at "International Journal of Impact Engineering"
DOI: 10.1016/j.ijimpeng.2017.12.021
Abstract: Abstract Armor-piercing (AP) projectiles generally carry a hard core within a copper jacket. Upon impact on a hard target, the copper case is stripped, while the core pierces the target. The cores of the most…
read more here.
Keywords:
steel cores;
piercing projectiles;
tool steel;
armor piercing ... See more keywords
Sign Up to like & get
recommendations!
1
Published in 2020 at "Optics and Laser Technology"
DOI: 10.1016/j.optlastec.2020.106120
Abstract: Abstract In this study, composite coatings were fabricated by preplacing a TiC layer on H13 tool steel and surface melting with a pulsed Nd: YAG laser. Since the morphology of hard phase particles is one…
read more here.
Keywords:
morphology;
composite coating;
tool steel;
h13 tool ... See more keywords