Tribological Behavior and Wear Mechanism of TZ20 Titanium Alloy After Various Treatments
Sign Up to like & getrecommendations! Published in 2018 at "Journal of Materials Engineering and Performance"
DOI: 10.1007/s11665-018-3570-9
Abstract: Abrasion is one of the most common failure forms of metals and alloys. The study of the friction and wear behavior of metals and alloys is greatly beneficial to improve their long life and safe… read more here.
Keywords: various treatments; wear; wear mechanism; normal load ... See more keywords
Effect of applied load on transition behavior of wear mechanism in Cu−15Ni−8Sn alloy under oil lubrication
Sign Up to like & getrecommendations! Published in 2017 at "Journal of Central South University"
DOI: 10.1007/s11771-017-3583-9
Abstract: Tribological behavior of Cu−15Ni−8Sn (mass fraction, %) alloy against GCr15 ring under various loads was investigated on a ring-on-block tester in oil lubrication. The results showed that the wear rate increased slowly from 1.7×10−7 to… read more here.
Keywords: alloy; mechanism; transition; wear mechanism ... See more keywords
Investigation on Tribological Behaviour of Aluminosilicate Reinforced AA7075 Composites for Aviation Application
Sign Up to like & getrecommendations! Published in 2020 at "Transactions of The Indian Institute of Metals"
DOI: 10.1007/s12666-020-02112-6
Abstract: In this study, AA 7075 and its composites were developed using ex situ (stir casting) process for varying compositions 1–3 in weight fraction (wt%) of aluminosilicate (nanoclay) at an interval of 1 wt%. The developed… read more here.
Keywords: wear mechanism; matrix material; nanoclay; aluminosilicate ... See more keywords
Dry Sliding Wear Mechanism Maps of Al–7Si–0.3Mg Hybrid Composite: Novel Approach of Agro-Industrial Waste Particles to Reduce Cost of Material
Sign Up to like & getrecommendations! Published in 2019 at "Journal of Bio- and Tribo-Corrosion"
DOI: 10.1007/s40735-019-0227-7
Abstract: Waste materials are one of the biggest threats facing the environment today. In the present work, an attempt has been made by the utilization of waste materials into raw materials to reduce the material cost… read more here.
Keywords: mechanism; dry sliding; waste; hybrid composite ... See more keywords
Novel gradient alloy steel with quasi-continuous ratios fabricated by SLM: Material microstructure and wear mechanism
Sign Up to like & getrecommendations! Published in 2021 at "Materials Characterization"
DOI: 10.1016/j.matchar.2021.111020
Abstract: Abstract In this work, a quasi-continuous ratio gradient alloy steel with a 24CrNiMo matrix for high-speed railway brake discs is prepared by selective laser melting (SLM). The composition of sample is x% 24CrNiMo + (1-x)% wear-resistant stainless… read more here.
Keywords: steel; wear mechanism; alloy steel; microstructure wear ... See more keywords
Effect of quench-tempering conditions prior to nitriding on microstructure and fretting wear mechanism of gas nitrided X210CrW12 steel
Sign Up to like & getrecommendations! Published in 2019 at "Surface and Coatings Technology"
DOI: 10.1016/j.surfcoat.2018.12.066
Abstract: Abstract In this research the effect of quench-tempering conditions prior to industrial gas nitriding on the microstructure, fretting wear behavior and mechanism of nitrided X210CrW12 steel was investigated. The results reveal that higher tempering temperature… read more here.
Keywords: quench tempering; wear mechanism; layer; tempering conditions ... See more keywords
Effects of high-pressure cooling in the flank and rake faces of WC tool on the tool wear mechanism and process conditions in turning of alloy 718
Sign Up to like & getrecommendations! Published in 2019 at "Wear"
DOI: 10.1016/j.wear.2019.05.037
Abstract: The exceptional properties of Heat Resistant Super Alloys (HRSA) justify the search for advanced technologies that can improve the capability of machining these materials. One such advanced technology is the application of a coolant at… read more here.
Keywords: high pressure; alloy 718; wear mechanism; pressure ... See more keywords
Wear-out Mechanism of Press-pack IGBTs Under Accelerated Aging Test
Sign Up to like & getrecommendations! Published in 2021 at "IEEE Journal of Emerging and Selected Topics in Power Electronics"
DOI: 10.1109/jestpe.2021.3085590
Abstract: The study of wear-out mechanism of press-pack IGBTs (PPIs) is conducted insufficiently now. In this paper, both the numerical and experimental methods are utilized to investigate the wear-out mechanism of PPIs. After conducting an accelerated… read more here.
Keywords: additional metallization; wear; wear mechanism; metallization area ... See more keywords
Wear behavior and wear mechanism of iron foam reinforced SiCp/A359 interpenetrating phases composites at high temperature
Sign Up to like & getrecommendations! Published in 2022 at "Journal of Composite Materials"
DOI: 10.1177/00219983221137674
Abstract: The A359-SiCp/Fe interpenetrating phase composites reinforced with three-dimensional network structure iron foam and 20 wt. % SiC particles were fabricated after the infiltration technique by using the newly developed vacuum assisted infiltration procedures. The dry-sliding… read more here.
Keywords: wear mechanism; iron foam; wear; temperature ... See more keywords
Wear Mechanism of Elastomers under the Direct Impact of Solid Particles in an Aqueous Medium
Sign Up to like & getrecommendations! Published in 2018 at "Journal of Friction and Wear"
DOI: 10.3103/s1068366618660030
Abstract: A single impact of a solid particle on the surface of rubber in an aqueous medium is simulated using a special installation. An experimental study made it possible to distinguish the stages and the destruction… read more here.
Keywords: medium; wear mechanism; impact solid; aqueous medium ... See more keywords
Wear Mechanism of Multilayer Coated Carbide Cutting Tool in the Milling Process of AISI 4340 under Cryogenic Environment
Sign Up to like & getrecommendations! Published in 2022 at "Materials"
DOI: 10.3390/ma15020524
Abstract: Cryogenic technique is the use of a cryogenic medium as a coolant in machining operations. Commonly used cryogens are liquid nitrogen (LN2) and carbon dioxide (CO2) because of their low cost and non-harmful environmental impact.… read more here.
Keywords: wear mechanism; aisi 4340; tool; milling process ... See more keywords