Limit analysis for partial-joint-penetration weld T-joints with arbitrary loading angles
Sign Up to like & getrecommendations! Published in 2020 at "Engineering Structures"
DOI: 10.1016/j.engstruct.2020.110459
Abstract: Abstract In the present study, limit analysis is performed for T-joints with partial-joint-penetration (PJP) weld by taking advantage of the slip-line field theory and von Mises failure criterion. The strength evaluation equations are derived from… read more here.
Keywords: strength; joint penetration; partial joint; weld joints ... See more keywords
Development, optimization and validation of ultrasonic testing for NDE of ELM coils
Sign Up to like & getrecommendations! Published in 2017 at "Fusion Engineering and Design"
DOI: 10.1016/j.fusengdes.2017.07.007
Abstract: Abstract Institute for Plasma Research (IPR) has been developing technologies appropriate towards realizing fusion relevant Edge Localized Mode (ELM) magnets in Tokamaks such as Joint European Torus (JET) and Steady State Superconducting Tokamak (SST-1). The… read more here.
Keywords: elm coils; validation; weld joints; elm ... See more keywords
Fe-bearing intermetallics transformation and its influence on the corrosion resistance of Al–Mg–Si alloy weld joints
Sign Up to like & getrecommendations! Published in 2020 at "Journal of materials research and technology"
DOI: 10.1016/j.jmrt.2020.11.077
Abstract: Abstract This work investigated the transformation of Fe-bearing intermetallics and its influence on the corrosion behavior of Al-Mg-Si alloy weld joints. The results showed that the size and type of Fe-bearing intermetallics determined the pitting… read more here.
Keywords: weld joints; influence corrosion; alloy weld; transformation ... See more keywords
Effect of TiC/TiC–TiB2 on microstructure and mechanical properties of spray formed 7055 aluminum alloy TIG welded joints
Sign Up to like & getrecommendations! Published in 2021 at "Journal of Materials Research and Technology"
DOI: 10.1016/j.jmrt.2021.08.146
Abstract: Abstract Owing to the notorious hot-crack susceptibility and severe softening fusion-weld joints of Al–Zn–Mg–Cu alloys, they are generally considered unweldable. In this study, TiC/7xxx (TC) and TiC–TiB2/7xxx (BC) aluminum matrix composites, fabricated by in-situ mixed-salt… read more here.
Keywords: tic tib2; weld joints; spray formed; microstructure mechanical ... See more keywords
Investigations on weld joints of 7075 alloy with Al–5Mg–1Zn composite fillers by arc welding
Sign Up to like & getrecommendations! Published in 2023 at "Ferroelectrics"
DOI: 10.1080/00150193.2023.2198367
Abstract: Abstract In this work, the semisolid stirring casting assisted ultrasonic treatment and multi-pass rolling methods were applied to fabricate TiCp/Al–5Mg–1Zn filler materials for tungsten inert gas welding of 7075-T651 aluminum alloy. After welding, various performances… read more here.
Keywords: alloy 5mg; joints 7075; investigations weld; 7075 alloy ... See more keywords
Effect of current pulsing on super 304HCu weld joints
Sign Up to like & getrecommendations! Published in 2019 at "World Journal of Engineering"
DOI: 10.1108/wje-07-2019-0207
Abstract: Super 304HCu super austenitic stainless steel tubes containing 2.3 to 3 (Wt.%) of copper (Cu) is used in superheaters and reheater tubings of nuclear power plants. In general, austenitic stainless steels welded by conventional constant… read more here.
Keywords: gtaw; microscopy; weld joints; super 304hcu ... See more keywords
Computation of residual stresses, distortion, and thermogravimetric analysis of Inconel 625 weld joints
Sign Up to like & getrecommendations! Published in 2020 at "Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science"
DOI: 10.1177/0954406220974058
Abstract: In the current investigation, Inconel 625 weld joints were fabricated by Activated tungsten inert gas (A-TIG) and Tungsten inert gas (TIG) welding techniques. The joint configurations employed square butt and V groove edge preparations. Residual… read more here.
Keywords: weld joints; distortion; tig; residual stresses ... See more keywords
Experimental investigation on resistance spot welding of dissimilar weld joints
Sign Up to like & getrecommendations! Published in 2020 at "Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering"
DOI: 10.1177/0954408920968351
Abstract: In the present study, galvanized High Strength Interstitial Free (HIF) steel sheets, and Dual Phase (DP780) steel sheets were used for the investigations. Resistance spot weld joints were fabricated between dissimilar steel sheets. The variation… read more here.
Keywords: weld joints; steel sheets; weld; resistance ... See more keywords
Investigation on the effect of process parameters on mechanical and microstructural properties of AA8011 similar FSW weld joints
Sign Up to like & getrecommendations! Published in 2022 at "Advances in Mechanical Engineering"
DOI: 10.1177/16878132221112146
Abstract: Friction stir welding (FSW) factors significantly impact the welding characteristics of AA 8011 and similar alloys weld joints produced by FSW. The tool pin profiles influence joint characteristics, weld quality, and joint strength. This study… read more here.
Keywords: tool; threaded pin; taper threaded; weld joints ... See more keywords